SquadPixel Esp-32 Wifi, Bluetooth, Dual Core Chip Development Board (ESP-WROOM-32)
High performance- ratio,small vol, easily embeded to other products,strong function with support lwip protocol, freertos,supporting three modes: ap, sta, and ap+sta,supporting lua program, easily to develop
SquadPixel ESP-32 WiFi, Bluetooth, Dual Core Chip Development Board
Are batteries included?
No
10 reviews for SquadPixel Esp-32 Wifi, Bluetooth, Dual Core Chip Development Board (ESP-WROOM-32)
3.8out of 5
★★★★★
★★★★★
5
★★★★★
2
★★★★★
1
★★★★★
0
★★★★★
2
Write a review
Show allMost HelpfulHighest RatingLowest Rating
★★★★★
Shibusarkar –
For low cost it’s actually worth buying. But the hall read sensor in built wasn’t working.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
navaneethan –
The media could not be loaded.
Very good produced but broken switch replace it
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
navaneethan –
I’m working on this board daily. It works fine. Each time when you program this board you need to press the boot button. That’s a negative.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Amandeep Singh –
On reading slightly negative comments on this product from the seller, I expected an Okayish built of the model ESP32 if not defective.
But on receiving the package, it was shining as a star. Clean decent and sturdy. The pins seem to be rock solid. Working seems great too until now. (Bought it 2 months before writing this review)
But beware, ESP32 is NOT breadboard compatible (you can only use one side of the pins at a time/I had to bend the pins slightly) which a is real problem as it has through hole pins mean to be inserted into a perfboard or breadboard.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Shibusarkar –
The media could not be loaded.
no issues with the product. wled project successfully done
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Ajanth B. –
After 15 days, it stopped turning on. now can’t return also.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Gopala Krishna Reddy –
Using the Arduino IDE, I could not upload any sketch to the ESP32. I get a, “A fatal error occurred: Failed to connect to ESP32: Timed out waiting for packet header”. The only way to get this board to upload was to hold the “Boot” button down while uploading the sketch, then it worked. Returning device…
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
hp –
Legit. Pretty good. Works with arduino studio.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Ayush Basak –
Code is not uploading directly. We need to solder an extra capacitor. Search in youtube for that
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
C s. –
It’s been a year I have been using this one and its running well
Shibusarkar –
For low cost it’s actually worth buying. But the hall read sensor in built wasn’t working.
navaneethan –
The media could not be loaded.
Very good produced but broken switch replace it
navaneethan –
I’m working on this board daily. It works fine. Each time when you program this board you need to press the boot button. That’s a negative.
Amandeep Singh –
On reading slightly negative comments on this product from the seller, I expected an Okayish built of the model ESP32 if not defective.
But on receiving the package, it was shining as a star. Clean decent and sturdy.
The pins seem to be rock solid.
Working seems great too until now.
(Bought it 2 months before writing this review)
But beware, ESP32 is NOT breadboard compatible (you can only use one side of the pins at a time/I had to bend the pins slightly)
which a is real problem as it has through hole pins mean to be inserted into a perfboard or breadboard.
Shibusarkar –
The media could not be loaded.
no issues with the product. wled project successfully done
Ajanth B. –
After 15 days, it stopped turning on. now can’t return also.
Gopala Krishna Reddy –
Using the Arduino IDE, I could not upload any sketch to the ESP32. I get a, “A fatal error occurred: Failed to connect to ESP32: Timed out waiting for packet header”. The only way to get this board to upload was to hold the “Boot” button down while uploading the sketch, then it worked. Returning device…
hp –
Legit. Pretty good. Works with arduino studio.
Ayush Basak –
Code is not uploading directly.
We need to solder an extra capacitor.
Search in youtube for that
C s. –
It’s been a year I have been using this one and its running well